Taking a break
We're taking a break moving shop and hope to be back soon. We hope to start shipping orders in Nov 2018.
The Pololu AltIMU-10 v5 is an inertial measurement unit (IMU) and altimeter that features the same LSM6DS33 gyro and accelerometer and LIS3MDL magnetometer as the MinIMU-9 v5, and adds an LPS25H digital barometer. An IC interface accesses ten independent pressure, rotation, acceleration, and magnetic measurements that can be used to calculate the sensor’s altitude and absolute orientation. The board operates from 2.5 to 5.5 V and has a 0.1" pin spacing.
The Pololu AltIMU-10 v5 is a compact (1.0 0.5) board that combines ST’s LSM6DS33 3-axis gyroscope and 3-axis accelerometer, LIS3MDL 3-axis magnetometer, and LPS25H digital barometer to form an inertial measurement unit (IMU) and altimeter; we therefore recommend careful reading of the LSM6DS33 datasheet (1MB pdf), LIS3MDL datasheet (2MB pdf), and LPS25H datasheet (1MB pdf) before using this product. These sensors are great ICs, but their small packages make them difficult for the typical student or hobbyist to use. They also operate at voltages below 3.6 V, which can make interfacing difficult for microcontrollers operating at 5 V. The AltIMU-10 v5 addresses these issues by incorporating additional electronics, including a voltage regulator and a level-shifting circuit, while keeping the overall size as compact as possible. The board ships fully populated with its SMD components, including the LSM6DS33, LIS3MDL, and LPS25H, as shown in the product picture.
Compared to the previous AltIMU-10 v4, the v5 version uses newer MEMS sensors that provide some increases in accuracy (lower noise and zero-rate offsets). The AltIMU-10 v5 is pin-compatible with the AltIMU-10 v4, but because it uses different sensor chips, software written for older IMU versions will need to be changed to work with the v5.
The AltIMU-10 v5 is also pin-compatible with the MinIMU-9 v5 and offers the same functionality augmented by a digital barometer that can be used to obtain pressure and altitude measurements. It includes a second mounting hole and is only 0.2 longer than the MinIMU-9 v5. Any code written for the MinIMU-9 v5 should also work with the AltIMU-10 v5.
The LSM6DS33, LIS3MDL, and LPS25H have many configurable options, including dynamically selectable sensitivities for the gyro, accelerometer, and magnetometer and selectable resolutions for the barometer. Each sensor also has a choice of output data rates. The three ICs can be accessed through a shared IC/TWI interface, allowing the sensors to be addressed individually via a single clock line and a single data line. Additionally, a slave address configuration pin allows users to change the sensors’ IC addresses and have two AltIMUs connected on the same IC bus. (For additional information, see the IC Communication section below.)
The nine independent rotation, acceleration, and magnetic readings provide all the data needed to make an attitude and heading reference system (AHRS), and readings from the absolute pressure sensor can be easily converted to altitudes, giving you a total of ten independent measurements (sometimes called 10DOF). With an appropriate algorithm, a microcontroller or computer can use the data to calculate the orientation and height of the AltIMU board. The gyro can be used to very accurately track rotation on a short timescale, while the accelerometer and compass can help compensate for gyro drift over time by providing an absolute frame of reference. The respective axes of the two chips are aligned on the board to facilitate these sensor fusion calculations. (For an example of such a system using an Arduino, see the picture below and the Sample Code section at the bottom of this page.)
The carrier board includes a low-dropout linear voltage regulator that provides the 3.3 V required by the LSM6DS33, LIS3MDL, and LPS25H, allowing the module to be powered from a single 2.5 V to 5.5 V supply. The regulator output is available on the VDD pin and can supply almost 150 mA to external devices. The breakout board also includes a circuit that shifts the IC clock and data lines to the same logic voltage level as the supplied VIN, making it simple to interface the board with 5 V systems. The board’s 0.1" pin spacing makes it easy to use with standard solderless breadboards and 0.1" perfboards.
- Dimensions: 1.0 0.5 0.1 (25 mm 13 mm 3 mm)
- Weight without header pins: 0.8 g (0.03 oz)
- Operating voltage: 2.5 V to 5.5 V
- Supply current: 5 mA
- Output format (IC):
- Gyro: one 16-bit reading per axis
- Accelerometer: one 16-bit reading per axis
- Magnetometer: one 16-bit reading per axis
- Barometer: 24-bit pressure reading (4096 LSb/mbar)
- Sensitivity range:
- Gyro: 125, 245, 500, 1000, or 2000/s
- Accelerometer: 2, 4, 8, or 16 g
- Magnetometer: 4, 8, 12, or 16 gauss
- Barometer: 260 mbar to 1260 mbar (26 kPa to 126 kPa)
A 16 strip of 0.1" header pins and a 15 strip of 0.1" right-angle header pins are included. You can solder the header strip of your choice to the board for use with custom cables or solderless breadboards or solder wires directly to the board itself for more compact installations. The board features two mounting holes that work with #2 or M2 screws (not included).
- Product Wiki
- LSM6DS33 datasheet: Datasheet for the ST LSM6DS33 3D accelerometer and 3D gyroscope.
- AN4682: LSM6DS33 application note: This application note from ST provides usage information and application hints for the LSM6DS33 accelerometer and gyro.
- LIS3MDL datasheet: Datasheet for the ST LIS3MDL 3-axis magnetometer.
- AN4602: LIS3MDL application note: This application note from ST provides usage information and application hints for the LIS3MDL magnetometer.
- LPS25H datasheet: Datasheet for the ST LPS25H MEMS pressure sensor.
- UM10204 IÂ²C-bus specification and user manual: The official specification for the IÂ²C-bus, which is maintained by NXP.
- AltIMU-10 v5 schematic diagram: Printable schematic diagram of the AltIMU-10 v5 Gyro, Accelerometer, Compass, and Altimeter (LSM6DS33, LIS3MDL, and LPS25H Carrier).
- Dimension diagram of the AltIMU-10 v5 Gyro, Accelerometer, Compass, and Altimeter (LSM6DS33, LIS3MDL, and LPS25H Carrier)
- Drill guide for the AltIMU-10 v5 Gyro, Accelerometer, Compass, and Altimeter (LSM6DS33, LIS3MDL, and LPS25H Carrier): This DXF drawing shows the locations of all of the board’s holes.
- LSM6 library for Arduino: An Arduino library for interfacing with the LSM6DS33 accelerometer and gyro.
- LIS3MDL library for Arduino: An Arduino library for interfacing with the LIS3MDL magnetometer.
- LPS Arduino library: This is a library for the Arduino that interfaces with our LPS25H and LPS331AP pressure/altitude sensor carriers as well as the pressure sensor on the AltIMU-10 v3 (it also works with the original AltIMU-10). It makes it simple to read the raw pressure data from the sensor, and it provides functions to help calculate altitude based on the measured pressure.
- MinIMU-9 + Arduino AHRS:
This Arduino program (sketch) allows an Arduino connected to a MinIMU-9 v5 or AltIMU-10 v5 (or older versions of those boards) to function as an attitude and heading reference system, calculating estimated roll, pitch, and yaw angles from sensor readings that can be visualized with a 3D test program on a PC. It is based on the work of Jordi Munoz, William Premerlani, Jose Julio, and Doug Weibel.
Visualization of AHRS orientation calculated from MinIMU-9 readings.
- Quick and Dirty Compass Calibration in 3d: A blog post by Michael Shimniok about calibrating the magnetometer in the LSM303DLH and visualizing magnetic distortions. This information can generally be applied to other magnetometers as well.
- New products: MinIMU-9 and AltIMU-10 v5 IMU boards: We have released new versions of our MinIMU-9 and AltIMU-10 inertial measurement unit (IMU) modules, which use an IÂ²C interface to provide nine...
AltIMU-10 v5 Gyro, Accelerometer, Compass, and Altimeter (LSM6DS33, LIS3MDL, and LPS25H Carrier) 
- Brand: Pololu
- Product Code: POL-2739
- Reward Points: 21
- Availability: Out Of Stock
- Ex Tax: £21.95
- Price in reward points: 300