This in-system programmer can be used to program AVR microcontrollers and AVR-based controller boards, such as our Orangutan robot controllers and the 3pi robot. The programmer emulates an STK500 on a virtual serial port, making it compatible with standard AVR programming software, and it supports devices running at either 3.3 V or 5 V. The programmer also features a TTL-level serial port, enabling general-purpose serial communication for debugging or programming microcontrollers with a serial bootloader. An ISP cable and a 16 double-sided male header are included with the fully-assembled programmer.
The Pololu USB AVR Programmer v2 is a compact, low-cost in-system programmer (ISP) for Atmel’s AVR microcontrollers. The programmer provides an interface for transferring a compiled AVR program from your computer to the target AVR’s non-volatile memory, allowing it to run the program. It is a good solution for programming AVR-based controllers like the Orangutan robot controllers, and it can also be used to update, replace, or remove the bootloader on Arduino boards and our Arduino-compatible A-Star 32U4 controllers. This programmer is designed to work well with both 3.3 V and 5 V devices, and it can even be configured to provide power to the target device in low-power systems.
The programmer connects to your computer’s USB port via a standard USB A to Micro-B cable (not included) and communicates with your programming software, such as Atmel Studio, AVRDUDE, or Arduino, through a virtual COM port using the STK500 protocol. The programmer connects to your target device via an included 6-pin ISP programming cable (the older, 10-pin ISP connections are not directly supported, but it’s easy to create or purchase a 6-pin-to-10-pin ISP adapter). The programmer also acts as a USB-to-TTL serial adapter, providing a TTL-level serial port that can be used to communicate with other serial devices from your computer. It ships fully assembled with connectors soldered in as shown.
This product requires a USB A to Micro-B cable to connect to a computer.
Features and specifications
- Connects to a computer through USB via a USB A to Micro-B cable (not included)
- Emulates an STK500 programmer through virtual COM port interface
- Works with standard AVR programming software, including Atmel Studio, AVRDUDE, and the Arduino IDE
- Configuration software available for Windows, Mac OS X, and Linux
- Supports both 3.3 V and 5 V devices; can automatically switch operating voltage based on detected target VCC
- Can optionally power the target at 3.3 V or 5 V in low-power systems
- USB-to-TTL serial adapter functionality for general-purpose serial communication
- Provides a 100 kHz clock output, which can be useful for reviving misconfigured AVRs
- All I/O pins are protected with 470 resistors
- 6-pin ISP cable and a 16 double-sided male header included
- Comprehensive user’s guide
Supported AVR microcontrollers
The programmer should work with all AVRs that can be programmed with the AVR ISP (in-system programming) interface, which is also known as in-circuit serial programming (ICSP), serial programming, or serial downloading, but it has not been tested with all devices. We expect it to work with most AVRs in the megaAVR (ATmega) family, and it works with some members of the tinyAVR (ATtiny) family, but it does not support the Tiny Programming Interface (TPI), and it does not work with the XMEGA family or with 32-bit AVRs. The programmer features upgradable firmware, allowing updates for future devices.
The programmer is designed for use with AVR microcontrollers running at either 3.3 V or 5 V. By default, the programmer expects the target to be self-powered, but it can be configured to deliver power to the target device in low-power systems.
Supported operating systems
We support using the Pololu USB AVR Programmer v2 and its configuration software on desktop versions of Windows (Vista, 7, 8, and 10), Linux, and Mac OS X 10.11 or later. Older versions of Windows are not supported.
Bonus feature: TTL-level serial port
This programmer doubles as a USB-to-serial adapter. The programmer installs as two virtual COM ports: one for communicating with programming software and one for general-purpose serial communications. This means that you can seamlessly switch between programming an AVR and debugging it through the TTL serial port without having to open and close your terminal program. In addition to the serial transmit (TX) and receive (RX) lines, the programmer lets you use A and B as serial handshaking lines that can be configured using our software.
The six pins on the serial header (GND, A, VCC, TX, RX, and B) are arranged to be similar to the pinout of commonly-available FTDI USB-to-serial cables and breakout boards. In the default configuration, pin B is used as the DTR output (and pin A is an unused input), which allows you to plug the programmer directly into a variety of Arduino-compatible boards and use it to upload programs to the board via a serial bootloader.
The Pololu USB AVR Programmer v2 ships fully assembled with ISP and serial connectors soldered in, and it includes the accessories shown in the picture below. The 6-pin ISP cable can be used to program AVRs. The 16 double-sided male header can be plugged into the serial header to effectively reverse its gender (making it possible to connect that header to a breadboard or female jumper wires).
Comparison to the older Pololu USB AVR Programmer
The Pololu USB AVR Programmer v2 is an updated version of our Pololu USB AVR Programmer. It features a number of improvements compared to the original:
- Support for devices operating at 3.3 V (in addition to 5 V)
- VCC pin can be configured to provide 3.3 V or 5 V power to target in low-power systems
- Protection resistors on all I/O lines
- More accurate emulation of the ISP frequencies provided by the STK500; you can use the user interfaces of Atmel Studio and AVRDUDE to set your ISP frequency more easily
- Usability enhancements for serial interface, such as a more standard pin arrangement (similar to FTDI) and a pre-populated female header
This programmer does not include a USB cable, and it does not have the SLO-scope bonus feature. In addition to these changes, many other details are different between the v2 programmer and the original; please be sure to refer to the user’s guide for the USB AVR Programmer v2 to familiarize yourself with this programmer. This programmer was released in March 2016, so any written references to the “Pololu USB AVR Programmer” from before that time refer to the original (older) programmer.
- Product Wiki
- Pololu USB AVR Programmer v2 User’s Guide: User’s manual for the Pololu USB AVR Programmer v2.
- Pololu AVR Programming Quick Start Guide: This guide explains how to get started programming your Orangutan or 3pi Robot in Windows, Linux or Mac OS X. It covers setting up an AVR development environment (Atmel Studio for Windows users), installing the Pololu AVR C/C++ Library, and setting up the Pololu USB AVR Programmer.
- Pololu USB AVR Programmer v2 Software and Drivers for Windows: This installer contains the drivers and software for the Pololu USB AVR Programmer v2 for Microsoft Windows.
- Pololu USB AVR Programmer v2 Software for Mac OS X: This installer contains the software for the Pololu USB AVR Programmer v2 for Mac OS X.
- Pololu AVR Development Bundle for Windows: This bundle contains all the Pololu software you need to get started programming AVRs in Windows: the Pololu AVR C/C++ Library, the Pololu USB AVR Programmer drivers and software, and the Pololu Orangutan SVP drivers. We recommend installing Atmel Studio 7.0 before installing this bundle.
- Dimension diagram of the Pololu USB AVR Programmer v2
- Drill guide for the Pololu USB AVR Programmer v2: This DXF drawing shows the locations of all of the board’s holes.
- Pololu USB AVR Programmer v2 software source code: Source code for the Pololu USB AVR Programmer v2 software on GitHub.
- Atmel Studio: Atmel’s free integrated development environment (IDE) for AVRs.
- Atmel Web Page: Web page of Atmel Corporation, manufacturer of AVR microcontrollers and other advanced semiconductors.
- WinAVR: A free, open-source suite of development tools for the AVR family of microcontrollers, including the GNU GCC compiler for C/C++.
- CrossPack for AVR Development: Distribution of AVR development libraries and tools for Mac OS X.
- AVRDUDE: AVRDUDE is a cross-platform command-line utility for programming the flash memory on AVR microcontrollers.
- Arduino Software: Arduino integrated development environment (IDE) software
- AVR Libc Home Page: The web site for AVR Libc, which is the standard library of functions that you can use with C and C++ on the AVR.
- GCC, the GNU Compiler Collection: Documentation for GCC, including the AVR GCC C/C++ compilers.
- Pololu Robotics Forum: Pololu Robotics and Electronics forum — get technical support, share your project, or just drop in to say hi.
- AVR Freaks: AVR community with forums, projects, and AVR news.
- New product: Pololu USB AVR Programmer v2: I am excited to announce the release of the Pololu USB AVR Programmer v2, a programmer for the popular AVR microcontrollers from Atmel. Here at...
USB AVR Programmer v2 
- Brand: Pololu
- Product Code: POL-3170
- Reward Points: 12
- Availability: Out Of Stock
- Ex Tax: £12.30
- Price in reward points: 200